Audiocenter UTA902DSP: 2-Channel Class D Power Amplifier with DSP, 2 x 500W
The Audiocenter UTA902DSP is a two-channel Class D power amplifier with a built-in DSP, so the amplifier and the speaker processing are in one compact 2U box. Set your crossover, EQ, delay and limiter from the front-panel LCD or from a computer, and drive your speakers and subwoofers directly.
It delivers 2 x 500W into 8 ohms and can be bridged for subwoofers. It weighs just 5kg, which makes it a good fit for mobile PA and DJ rigs, hire stock and fixed installations alike.
Key features
- Amplifier and processor in one: built-in DSP with high-pass and low-pass filters, EQ, delay, compressor and limiter, so a separate speaker processor is not needed for many systems.
- 2 x 500W into 8 ohms, 2 x 900W into 4 ohms: enough to drive a pair of active-quality full-range speakers or subwoofers from one unit.
- Bridgeable for subwoofers: a 500W full-range amplifier that can be bridged up to 1400W for a subwoofer.
- FIR filtering: 512 taps per channel for linear-phase processing that keeps the transient detail of the original signal.
- Class D with PFC: efficiency over 90%, less heat and lower power use, with a 100-240V auto-adapting supply that copes with unstable mains.
- Light and compact: 2U rack height and 5.0kg.
- Easy to use: set the unit up from the LCD screen on the front panel, and store and recall presets.
- Quiet cooling: a stepless fan that adjusts its speed automatically.
Powerful DSP processing
- IIR filters: Butterworth, Linkwitz-Riley and Bessel filter types, from 6dB per octave up to 48dB per octave, for accurate low-cut and high-cut settings.
- Input section: noise gate, volume, phase and mute, with a 15-band EQ, high-pass and low-pass filters and up to 20ms of delay per channel.
- Output section: 15-band EQ, high-pass and low-pass filters, up to 20ms of delay per channel, a compressor and a limiter.
- BrainCore and Limita processing: Audiocenter's processing technology to keep the system working safely and protect your speakers.
- Presets: channel presets and system presets, so you can save and recall a setup for each speaker or venue.
Network control for installations
The UTA902DSP has a USB-B port and an RJ45 network port with UDP control. On a network, several amplifiers can be configured and updated together, with remote control and real-time adjustment from a computer. This helps on fixed installs such as venues, schools and hospitality, where you want to set the system once and manage it from a central point.
Where it is used
- Mobile DJs and bands: a light amplifier that also acts as the crossover for tops and subs.
- Subwoofers: bridge the amplifier to put up to 1400W into a subwoofer.
- Hire companies: one amplifier and one set of presets to cover several speaker types.
- Fixed installations: bars, clubs, restaurants, schools and churches that need processing and amplification in a small rack space.
Installation note
The amplifier is cooled by a fan that draws air from front to back. Leave the front and rear free of obstruction when it is mounted in a rack.
Frequently asked questions
Do I need a separate speaker processor with the UTA902DSP?
For many systems, no. The amplifier has a built-in DSP with crossover filters, EQ, delay, a compressor and a limiter, so you can set up a top and subwoofer system without a separate processor. For large or complex systems you can still use an external processor.
How much power does it deliver?
It delivers 2 x 500W into 8 ohms and 2 x 900W into 4 ohms. Bridged, it delivers 1400W into 8 ohms and 1800W into 4 ohms, which suits subwoofers. Check the impedance of your speakers before you connect them.
Can I control it from a computer?
Yes. It has a USB-B port and an RJ45 network port with UDP control, so you can configure it from a computer and manage several amplifiers over a network. You can also set it up from the LCD on the front panel.
Will it work on New Zealand power?
Yes. The power supply accepts 100-240V at 50 or 60Hz, so it works on New Zealand mains.
What do I connect to the inputs and outputs?
The inputs are balanced XLR (male and female) on each channel. The outputs are Speakon and binding posts, so you can use standard speaker cables.
Questions about speakers or system design? Contact us and we will help you choose the right amplifier and speakers for your use.